Physical Address

304 North Cardinal St.
Dorchester Center, MA 02124

What Are Two Tasks That Must Be Completed Before Two Routers Can Use OSPF To Form A Neighbor Adjacency Choose Two?

There are two tasks that need to be completed before OSPF can be used to form a neighbor adjacency. Choose two. The routers have to make a choice. The network type must be agreed upon by the routers. The dead interval must be used by the routers.

What Conditions Must Be Met Before Two Routers Running OSPF Will Share Information?

There are certain conditions that must be met in order to become neighbors. The Hello and Dead interval values have to match each other. The OSPF area ID is the same as the routers’s.

What Are Two Features Of The OSPF Routing Protocol Choose Two?

There are two features of OSPF. Choose two.

li>has an administrative distance of 100 used primarily as an EGP./li>

What Are Two Factors That Will Prevent Two Routers From Forming An Ospfv2 Adjacency Choose Two?

There is a missing OSPF network command. Mismatched IOS versions, the use of private IP addresses, and different types of interface ports used on a switch aren’t causes for an OSPF adjacency failing to form between two routers.

What Could Be Reason For OSPF Neighbors Being Stuck In 2 Way?

PauseOSpf routers on multi-access segments have their databases synchronized with their DR or BDR only If at least one of the two routers is a DR or BDR, the OSPF status will be Full. The state is still Two-way between the two routers.

Do OSPF Neighbors Have To Be Directly Connected?

PauseOSPF is an inter-AS dynamic route. Since an autonomously formed system is formed by a connected set of routers are always connected The neighbors are the ones that are directly accessible.

What Criteria Must Match Before An Adjacency Is Formed Between 2 Routers?

There are requirements for OSPF Adjacency.

The devices must be in the same area.

What Are The Features Of OSPF?

OSPF provides/supports advantages.

Load balancing with equal cost routes for the same destination.

What Happens Immediately After Two OSPF Routers Have Exchanged?

What happens after two OSPF routers have exchanged hello packets? They exchange packets to advertise certain parameters. The election process can be negotiated if they are on a multiaccess network.

What Are Two Features Of OSPFv3?

OSPFv2 features are included in OSPFv3 implements.

li>Packet types./li>li>Neighbor discovery and adjacency formation mechanisms.

What are the neighborship requirements?

The OSPF Neighborship requirements are explained in detail with examples. The configuration values on the two routers can’t be compared. It is not possible for OSPF to share information with neighbors.

Do you need to match hello packet to be a neighbor?

The configuration values in a hello packet must be the same on both the routers that want to build a neighborship. We will explain the configuration values with an example. It is necessary to match values on both routers in order to become a neighbor.

Do you need the same flag?

If you want to build an OPSF neighborship, you need the same flag. neighborship can be built if both the R1 and R2 are in the same area.

How can we set a lower priority?

Choose two. R2 has a lower priority. The same area should be configured for the routers. R2 is a lower cost than R1. A backup is added to the network. The hello and dead timers should be matched. The same area should be configured for the routers. The hello and dead timers should be matched.

/li>

What Are The Neighborship Requirements For OSPF Routers?

The OSPF Neighborship requirements are explained in detail with examples. The configuration values on the two routers can’t be compared. It is not possible for OSPF to share information with neighbors.

Do You Have To Match Hello Packet To Become OSPF Neighbor?

The configuration values in a hello packet must be the same on both the routers that want to build a neighborship. We will explain the configuration values with an example. It is necessary to match values on both routers in order to become a neighbor.

Do You Need Same Stub Flag For OPSF Neighborship?

If you want to build an OPSF neighborship, you need the same flag. neighborship can be built if both the R1 and R2 are in the same area.

How To Set A Lower Priority On R2?

Choose two. R2 has a lower priority. The same area should be configured for the routers. R2 is a lower cost than R1. A backup is added to the network. The hello and dead timers should be matched. The same area should be configured for the routers. The hello and dead timers should be matched.